SixXS::Sunset 2017-06-06

tunnel trough a cisco 827 router
[nl] Shadow Hawkins on Wednesday, 30 March 2005 12:13:38
I want to set up a ipv6 tunnel trough a cisco 827 router. But it's blocking the traffic and says it's spoofing... The lan side of the cisco is nat. With the previous router i had a working setup, so guess i have to change something on the cisco, anyone any idea what can be wrong in the router?
tunnel trough a cisco 827 router
[ch] Jeroen Massar SixXS Staff on Wednesday, 30 March 2005 13:55:51
What about upgrading the Cisco to an IOS that does IPv6?
tunnel trough a cisco 827 router
[nl] Shadow Hawkins on Wednesday, 30 March 2005 14:34:58
as far as i can see IOS 12.2 YA8 supports ipv6...... but i can't find a way to get my tunnel through the cisco.....
tunnel trough a cisco 827 router
[nl] Shadow Hawkins on Wednesday, 06 April 2005 18:54:04
Ivo, Can you send me your configuration? It should work on 827 .... Willem.
tunnel trough a cisco 827 router
[nl] Shadow Hawkins on Thursday, 07 April 2005 18:48:58
My cisco ipv6 config: The Tunnel interface: interface Tunnel0 no ip address ipv6 address <SIXXS Endpoint IPv6 Address>/64 tunnel source <IPv4 Local Address> tunnel destination <IPv4 SIXXS POP Address> tunnel mode ipv6ip ! The local LAN interface: interface Ethernet0/0 ipv6 address <SIXXS Subnet>/64 ipv6 enable ipv6 mtu 1280 ipv6 nd ra-interval 60 ipv6 nd ra-lifetime 180 ipv6 nd prefix-advertisement <SIXXS Subnet>/64 360 60 autoconfig !
tunnel thru a cisco 827 router
[it] Shadow Hawkins on Saturday, 11 June 2005 13:07:01
Have you ever tried ipv6 cef (Cisco Express forwarding?) Matteo Rinaudo
tunnel thru a cisco 827 router
[it] Shadow Hawkins on Saturday, 11 June 2005 13:11:18
These acl can also be useful: interface Dialer0 ipv6 traffic-filter fw-in in ipv6 traffic-filter fw-out out ipv6 access-list fw-in permit tcp any any established permit tcp any any eq ident permit icmp any any echo-request permit icmp any any echo-reply permit icmp any any packet-too-big permit icmp any any time-exceeded permit icmp any any unreachable deny ipv6 any any log ipv6 access-list fw-out permit ipv6 any any Matteo Rinaudo
tunnel thru a cisco 827 router
[it] Shadow Hawkins on Saturday, 11 June 2005 13:05:39
Hi, I have a Cisco 1417 with IOS 12.3(13). Do you have a static or a dynamic IPv4 endpoint? If it is dynamic, do you update it with `aiccu' from your workstation? Matteo Rinaudo
tunnel thru a cisco 827 router
[de] Carmen Sandiego on Tuesday, 02 August 2005 00:06:41
Yes, thats how it is done. Just grab the snipplets from the configure-faq. Regards, rm
tunnel trough a cisco 827 router
[nl] Shadow Hawkins on Friday, 26 August 2005 15:03:33
How about the following lines:
ipv6 unicast-routing ipv6 cef ipv6 route 2000::/3 2001:888:10:FA::1
You may not need the CEF line but the other two are vital.

Please note Posting is only allowed when you are logged in.

Static Sunset Edition of SixXS
©2001-2017 SixXS - IPv6 Deployment & Tunnel Broker