SixXS::Sunset 2017-06-06

install subnet
[no] Carmen Sandiego on Sunday, 04 January 2009 23:12:22
Tried to install subnet, i added 2001:16d8:ee41::1 on eth0 but its not working. and i followed the howto install subnet on SixXs wiki... my tunnel IPv6: 2001:16d8:ee00:76::2 My subnet IPv6: 2001:16d8:ee41::/48 Here is my ifconfig.. running Debian. FKDebian:/etc# ifconfig eth0 Link encap:Ethernet HWaddr 00:0c:29:21:e6:03 inet addr:82.148.***.** Bcast:82.148.147.255 Mask:255.255.254.0 inet6 addr: 2001:16d8:ee41::1/64 Scope:Global inet6 addr: 2001:16d8:ee00:76::4/64 Scope:Global inet6 addr: fe80::20c:29ff:fe21:e603/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:20945703 errors:27607 dropped:0 overruns:0 frame:0 TX packets:1373475 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4125928854 (3.8 GiB) TX bytes:129183176 (123.1 MiB) Interrupt:169 Base address:0x1400 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:18771 errors:0 dropped:0 overruns:0 frame:0 TX packets:18771 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1913677 (1.8 MiB) TX bytes:1913677 (1.8 MiB) sixxs Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet6 addr: 2001:16d8:ee00:76::2/64 Scope:Global inet6 addr: fe80::14d8:ee00:76:2/64 Scope:Link UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1280 Metric:1 RX packets:332 errors:0 dropped:0 overruns:0 frame:0 TX packets:330 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:52054 (50.8 KiB) TX bytes:24764 (24.1 KiB)
install subnet
[ch] Jeroen Massar SixXS Staff on Monday, 05 January 2009 03:07:49
What is 2001:16d8:ee00:76::4/64 doing on eth0? Only <tun>::1 (PoP side of the tunnel) an <tun>::2 (Your end of the tunnel) exist, nothing else. Also you say "it is not working", but what exactly is "not working" ? Did you enable forwarding? Also, please actually read the "Reporting Problems / Checklist" on the contact page.
install subnet
[no] Carmen Sandiego on Monday, 05 January 2009 08:54:34
have removed 2001:16d8:ee00:76::4/64 from eth0. and, how do i install my subnet on the server, i don't want the server to be a DHCP yet.
install subnet
[ch] Jeroen Massar SixXS Staff on Monday, 05 January 2009 11:27:13
Subnets are for connecting OTHER hosts. See the FAQ for details.
install subnet
[us] Shadow Hawkins on Monday, 05 January 2009 14:52:51
I'm not sure if this will help you or not, but your tunnel interface needs to go from 2001:16d8:ee00:76::2 to 2001:16d8:ee00:76::1. Your server needs to advertise the 2001:16d8:ee41::/48 subnet, and if you're running autoconfigure, your system will set it's own IP for eth0.
install subnet
[ch] Jeroen Massar SixXS Staff on Monday, 05 January 2009 14:58:38
Your server needs to advertise the 2001:16d8:ee41::/48 subnet, and if you're running autoconfigure, your system will set it's own IP for eth0.
It is just a single /64 one needs to advertise, not the complete /48, autoconfig really only works with a /64. Also, not all kernels/OSs auto-configure their IP based on the presence of RA messages, especially not because if they are correctly implemented most don't accept RAs on interfaces that have forwarding enabled, and the latter is most likely what you want.
install subnet
[no] Carmen Sandiego on Tuesday, 06 January 2009 08:33:13
I have fix this problem :)

Please note Posting is only allowed when you are logged in.

Static Sunset Edition of SixXS
©2001-2017 SixXS - IPv6 Deployment & Tunnel Broker