Ticket ID: SIXXS #1290791 Ticket Status: User PoP:
AICCU hearbeat using Monowall does not work for me
![]()
I have read and followed the "Reporting Problems" section on the Contact page.
I am removing these five pre-filled lines to demonstrate that I really read it.
I am providing the full details as requested on the mentioned Contact page.
If I do not remove this, then please ignore this message as I didn't read it anyway.
------------------------------------------------------------------------------>8
Hello,
I am using latest stable monowall release and I have been trying to configure AICCU on the WAN interface, which also does PPPoE, but it seems I can not ping the remote IPv6 address from inside monowall (using exec.php script), do you have any clue ? This is the output of Monowall ifconfig -a
$ ifconfig -a
sis0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
options=8<VLAN_MTU>
inet 192.168.3.1 netmask 0xffffff00 broadcast 192.168.3.255
inet6 fe80::200:24ff:fec0:7d80%sis0 prefixlen 64 scopeid 0x1
inet6 2001:b18:403b:1::1 prefixlen 64
ether 00:00:24:c0:7d:80
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
sis1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
options=8<VLAN_MTU>
inet6 fe80::200:24ff:fec0:7d81%sis1 prefixlen 64 scopeid 0x2
ether 00:00:24:c0:7d:81
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
sis2: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
options=8<VLAN_MTU>
inet 192.168.0.1 netmask 0xffffff00 broadcast 192.168.0.255
inet6 fe80::200:24ff:fec0:7d82%sis2 prefixlen 64 scopeid 0x3
inet6 2001:b18:403b:2::1 prefixlen 64
ether 00:00:24:c0:7d:82
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
enc0: flags=41<UP,RUNNING> mtu 1536
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5
ng0: flags=88d1<UP,POINTOPOINT,RUNNING,NOARP,SIMPLEX,MULTICAST> mtu 1492
inet6 fe80::200:24ff:fec0:7d80%ng0 prefixlen 64 scopeid 0x6
inet 79.159.5.41 --> 192.168.153.1 netmask 0xffffffff
ng1: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng2: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng3: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng4: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng5: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng6: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng7: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng8: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng9: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng10: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng11: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng12: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng13: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng14: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng15: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng16: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
gif0: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1280
tunnel inet 79.159.5.41 --> 82.102.0.131
inet6 fe80::200:24ff:fec0:7d80%gif0 prefixlen 64 scopeid 0x17
inet6 2001:b18:2000:80::2 --> 2001:b18:2000:80::1 prefixlen 128
State change: user
![]() ![]()
The state of this ticket has been changed to user
AICCU hearbeat using Monowall does not work for me
a) try reading
b) contact monowall folks for monowall issues, or at least use the forums, the ticket system is when a PoP has issues, not for your issues.
AICCU hearbeat using Monowall does not work for me
![]()
I have read and followed the "Reporting Problems" section on the Contact page.
I am removing these five pre-filled lines to demonstrate that I really read it.
I am providing the full details as requested on the mentioned Contact page.
If I do not remove this, then please ignore this message as I didn't read it anyway.
------------------------------------------------------------------------------>8
Thank you Joroen and sorry, I was in a hurry, everything is working fine, the problem that I have now is that my access point does not support IPv6, but the PoP works well !
You can close/delete this ticket and sorry for the inconvinience.
|